Hot Pixel All articles
Sensor Tech

One Bright Dot in Every Night Shot? Let's Talk About Your Sensor's Little Liars

Hot Pixel
One Bright Dot in Every Night Shot? Let's Talk About Your Sensor's Little Liars

Photo: Charles J. Sharp, CC BY-SA 4.0, via Wikimedia Commons

Every photographer eventually meets The Dot. You're reviewing a 30-second exposure of the Milky Way over Joshua Tree, zoomed in at 400%, and there it is: a single pixel burning a hole through your otherwise perfect frame. Red, green, or blue, it doesn't move between shots, and no amount of editing makes it charming.

Welcome to the world of pixel-level defects. They're more common than camera makers admit, and mostly more annoying than serious. But knowing what you're looking at — and what it costs to fix — separates a quick DIY solution from an unnecessary $400 repair bill.

Hot, Stuck, Dead, or Dusty: Know Your Enemy

First, a field guide, because these terms get thrown around interchangeably and they shouldn't be.

Hot pixels are the overachievers of the defect world. They show up during long exposures or high ISO shooting, glowing like tiny embers. The culprit is heat: when a sensor's photodiode leaks current (a phenomenon called dark current), certain pixels accumulate charge without any light hitting them. The longer the exposure and the warmer the sensor, the worse it gets. Shoot a five-minute exposure on a summer night in Phoenix and you'll meet every hot pixel your sensor has.

Stuck pixels are always on, no matter the exposure length or ISO. A pixel locked to full red, green, or blue in every single frame — daylight snapshots included — is stuck.

Dead pixels are the opposite: permanently black, reading zero light regardless of conditions. Rare, but they happen.

Dust spots aren't pixel defects at all, but they masquerade as them. The tell: dust moves around (or disappears entirely) when you change focal lengths or aperture. A stuck pixel never moves. If your speck is soft-edged and blurry, it's a dust bunny on the sensor stack, not a broken pixel.

Diagnose It Properly Before You Panic

Here's the test that separates real defects from imagined ones. Cap the lens, set manual exposure to something like f/16 at 8 seconds, crank ISO to 1600, and shoot. Then take a second shot at 1/4000th of a second in daylight conditions. Compare the two at 100% magnification.

Also check whether your camera has a sensor cleaning or pixel mapping function buried in the menu. Most modern bodies from Canon, Sony, and Nikon include a feature that maps out stuck pixels and interpolates over them in-camera. It's not a hardware fix, but for JPEG shooters it's often all they need. Note that it usually doesn't apply to RAW files — your editor software is the backstop there.

The Warranty Question: When to Push, When to Shrug

Here's the uncomfortable truth: virtually no manufacturer considers a handful of stuck pixels a defect. Canon's official stance, like Sony's and Nikon's, allows for a small number of mapped pixels. One or two bright dots? You'll almost certainly get a "within specification" letter.

Where warranty claims get traction:

A reader in Portland told us a Sony service center replaced the sensor on his a7 IV under warranty after he documented a six-pixel cluster with side-by-side test shots and a written timeline. Documentation wins these fights. Screenshots with timestamps, EXIF data intact, sent within the first 30 days of ownership. Be polite, be specific, be persistent.

Out of warranty? Now we're talking real money.

What Repairs Actually Cost in the US

We called around to independent shops and authorized service centers in early 2025. Ballpark figures for sensor replacement on a mid-range mirrorless body:

That math matters. A stuck pixel on a $700 camera is a shrug-and-map-it situation. The same defect on a $4,000 body is worth a repair quote. And if the repair estimate creeps past half the camera's used market value, the answer is usually a replacement body or a very cheap used backup.

The Safe-versus-Reckless Cleaning Ladder

Since dust causes most false alarms, let's talk cleaning — because this is where people destroy $2,000 sensors.

Safe: A rocket blower. Lens off, camera facing down, squeeze. This handles 80% of dust situations and carries zero risk. Do this first, always.

Mostly safe: Wet swab method with proper sensor swabs and solution sized for your sensor format (full-frame swabs on APS-C waste money; APS-C swabs on full-frame waste time). One swipe, one swab, never reuse. Work in a clean room, not a garage.

Risky: Anything adhesive, anything that touches the sensor glass with pressure, canned air (the propellant can spit fluid and freeze surfaces), or — please, no — household cloths and Windex.

Never: Compressed air held too close, vacuum attachments, or repeated aggressive swabbing. The sensor stack's IR/AA filter layer is thinner than it looks, and scratches there are permanent and expensive.

The Verdict

Pixel defects are the herpes of digital imaging: common, mostly harmless, and manageable once you stop panicking. Map them in-camera, clone them in post, document them for warranty if they're bad enough, and save the repair budget for damage that actually spreads. Your night sky photos — and your wallet — will thank you.

All Articles

Related Articles

The Upgrade You Keep postponing Is the One Sitting in Your Closet

The Upgrade You Keep postponing Is the One Sitting in Your Closet

Two Bodies, One Wedding, Zero Clues: Our Blind Camera Test Humiliated Everyone

Two Bodies, One Wedding, Zero Clues: Our Blind Camera Test Humiliated Everyone

Glass Window or Tiny TV? What Your Viewfinder Choice Says About How You Shoot

Glass Window or Tiny TV? What Your Viewfinder Choice Says About How You Shoot